Post pics of your car in here
-
ICI
- Posts: 55
- Joined: August 30th, 2006, 9:02 pm
- Location: Rousse, Bulgaria
-
Contact:
Post
by ICI » October 8th, 2012, 11:29 pm
Urbancamo wrote:Hello.
Some serious power you get there, definately.
Keep up the good work.
T
Thanks :)
I did a little testing this night, big wheel spinning at 1st and too early 2nd shifting
http://www.youtube.com/watch?v=UvsHtj-w8HE
boost 1.4 bar, the times approx like that:
1/4 mile 11.5 sec @ 191 km/h
0-100 km/h 3.8 sec
0-200 km/h 13.5 sec
100-200 km/h 9.7 sec
powered by ICIDesign
-
tricky
- Posts: 101
- Joined: July 6th, 2010, 5:41 pm
Post
by tricky » October 9th, 2012, 8:14 am
That engine sounds truly sweet on track !
Twice as many valves
-
ICI
- Posts: 55
- Joined: August 30th, 2006, 9:02 pm
- Location: Rousse, Bulgaria
-
Contact:
Post
by ICI » October 9th, 2012, 11:18 am
tricky wrote:That engine sounds truly sweet on track !
yes, I love it :)
The track onboard at the previous page is filmed with GoPro cam and the sound is very clear and true.
Meanwhile, I soursed turbine housing 0.73 A/R, soon the improvement will take a place.
powered by ICIDesign
-
ICI
- Posts: 55
- Joined: August 30th, 2006, 9:02 pm
- Location: Rousse, Bulgaria
-
Contact:
Post
by ICI » October 24th, 2012, 9:25 pm
The new A/R .73 turbine housing is here, compared next to the old one A/R 1.06.
The difference is pretty big, may be near 1000 rpm earlier spool will be :)
-
Attachments
-

- Picture 631.jpg (162 KiB) Viewed 3661 times
-

- Picture 647.jpg (268.53 KiB) Viewed 3661 times
powered by ICIDesign
-
ICI
- Posts: 55
- Joined: August 30th, 2006, 9:02 pm
- Location: Rousse, Bulgaria
-
Contact:
Post
by ICI » October 25th, 2012, 10:48 pm
almost done, have to finish the 76mm full lenght stainless steel exhaust soon
-
Attachments
-

- IMGP6562.jpg (237.59 KiB) Viewed 3630 times
-

- IMGP6572.jpg (255.21 KiB) Viewed 3630 times
-

- IMGP6575.jpg (157.26 KiB) Viewed 3630 times
powered by ICIDesign
-
ICI
- Posts: 55
- Joined: August 30th, 2006, 9:02 pm
- Location: Rousse, Bulgaria
-
Contact:
Post
by ICI » October 29th, 2012, 9:06 pm
finaly, did it for my car also
-
Attachments
-

- IMGP6590.jpg (152.57 KiB) Viewed 3435 times
-

- IMGP6595.jpg (176.12 KiB) Viewed 3435 times
powered by ICIDesign
-
ICI
- Posts: 55
- Joined: August 30th, 2006, 9:02 pm
- Location: Rousse, Bulgaria
-
Contact:
Post
by ICI » November 4th, 2012, 10:28 pm
Unfortunately this evening the gearbox gave up.
I had boost creep issues with the Turbosmart 38mm wastegate together with the new 0.73 A/R turbine housing.
The boost was uncontrollable above 5000 rpm and I lost it few times up to 1.8 bar.
And a strong rattle and scratching noise appeared, obviously from 2 nd gear, the 1 st gear started whining too...
A lot of work has to be done.
powered by ICIDesign
Users browsing this forum: No registered users and 1 guest