Fiat RITMO ABARTH 125TC
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
Hi all, news for you :-)
first start of my engine:
http://www.youtube.com/watch?v=Ft8fggLMV_4
first drive with my cas:
http://www.youtube.com/watch?v=FV57WYh4 ... re=related
first sprint :-)
http://www.youtube.com/watch?v=YJUIYafCDtM
http://www.youtube.com/watch?v=cDOk0osE ... re=related
rgds
Luboš
first start of my engine:
http://www.youtube.com/watch?v=Ft8fggLMV_4
first drive with my cas:
http://www.youtube.com/watch?v=FV57WYh4 ... re=related
first sprint :-)
http://www.youtube.com/watch?v=YJUIYafCDtM
http://www.youtube.com/watch?v=cDOk0osE ... re=related
rgds
Luboš
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
before finish of my project
- Attachments
-
- a olejáč.jpg (90.31 KiB) Viewed 11728 times
-
- b cívky.jpg (83.64 KiB) Viewed 11728 times
-
- c pracovní prostor.jpg (100.81 KiB) Viewed 11728 times
-
- IC from Lancia Delta Integrale
- a.jpg (120.81 KiB) Viewed 11728 times
-
- IC in Ritmo
- 4.jpg (144.95 KiB) Viewed 11728 times
-
- no coment.. :-)
- c.jpg (158.61 KiB) Viewed 11728 times
Ritmo Abarth125TC
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
.
Last edited by AbarthLubos on July 26th, 2010, 6:55 pm, edited 1 time in total.
Ritmo Abarth125TC
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
Hi Guy, hi all.... first time I had in my Fiat 190PS, because it was not OK for me, I made update with 280PS. I drove my first 400m and problem was with my clutch. Very, very much skimmed. It was not good.
http://www.youtube.com/watch?v=KERoN3ItYqU
http://www.youtube.com/watch?v=h2BvL2YP1EA
After it I dismantled my Fiat and started new update
http://www.youtube.com/watch?v=KERoN3ItYqU
http://www.youtube.com/watch?v=h2BvL2YP1EA
After it I dismantled my Fiat and started new update
Ritmo Abarth125TC
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
my big dream 400PS and very much Nm
- Attachments
-
- For my Fiat I have special car
- pict_20100425_201218.jpg (22.81 KiB) Viewed 11064 times
-
- new clutch +40% press
- pict_20100526_211842.jpg (26.84 KiB) Viewed 11064 times
-
- old and new
- pict_20100526_211934.jpg (25.35 KiB) Viewed 11064 times
-
- lining
- pict_20100526_212149.jpg (23.39 KiB) Viewed 11064 times
-
- new parts for my engine
- pict_20100617_220537.jpg (29.41 KiB) Viewed 11064 times
-
- flywheel
- pict_20100620_202943.jpg (19.26 KiB) Viewed 11064 times
-
- a
- pict_20100617_221227.jpg (14.46 KiB) Viewed 11064 times
-
- new big IC
- pict_20100709_220447.jpg (27.92 KiB) Viewed 11064 times
-
- spritzer - injectors 850cc
- pict_20100527_160436.jpg (16.22 KiB) Viewed 11064 times
-
- new doors only 4,4kg
- pict_20100515_175526.jpg (21.52 KiB) Viewed 11064 times
-
- laminate new bonnet
- pict_20100606_130207.jpg (18.13 KiB) Viewed 11064 times
-
- a
- pict_20100606_130302.jpg (19.17 KiB) Viewed 11064 times
-
- a
- pict_20100606_130037.jpg (14.25 KiB) Viewed 11064 times
-
- a
- pict_20100606_130127.jpg (21.79 KiB) Viewed 11064 times
-
- no coment :-)
- pict_20100717_195236.jpg (34.03 KiB) Viewed 11064 times
-
- a
- pict_20100724_123844.jpg (37.73 KiB) Viewed 11064 times
-
- a
- pict_20100724_123953.jpg (55.86 KiB) Viewed 11064 times
-
- a
- pict_20100724_124102.jpg (48.64 KiB) Viewed 11064 times
-
- and...
- pict_20100710_154601.jpg (27.58 KiB) Viewed 11064 times
Ritmo Abarth125TC
-
- Posts: 39
- Joined: November 3rd, 2006, 6:02 pm
- Location: London, UK
- Contact:
Re: Fiat RITMO ABARTH 125TC
WOW great project sir, fantastic work.
May I enquire where you located the lightweight doors and tailgate and if it is possible to get a set for my 130tc?
Please mail me direct if this request or the subsequent answer contravene the rules of the forum.
contactstrada@strada130.co.uk
Regards
Mitchell Pescay
strada 130tc owners club GB
May I enquire where you located the lightweight doors and tailgate and if it is possible to get a set for my 130tc?
Please mail me direct if this request or the subsequent answer contravene the rules of the forum.
contactstrada@strada130.co.uk
Regards
Mitchell Pescay
strada 130tc owners club GB
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
news
- Attachments
-
- a.jpg (109.84 KiB) Viewed 11003 times
-
- b.jpg (120.77 KiB) Viewed 11003 times
Ritmo Abarth125TC
-
- Site Admin
- Posts: 5039
- Joined: June 18th, 2006, 9:31 am
- Location: Bedford, UK
- Contact:
Re: Fiat RITMO ABARTH 125TC
Great project and nicely presented!
The only remark I want to make is I do not like that header. Without wishing to 'spoil the party' I have done extensive flowtests on types same or exactly like that and the results are alarmingly bad. That is just part of the story however - I have written extensively about turbo header design in my new book (see GC Virtual Workshop) and you should read before proceeding.
G
The only remark I want to make is I do not like that header. Without wishing to 'spoil the party' I have done extensive flowtests on types same or exactly like that and the results are alarmingly bad. That is just part of the story however - I have written extensively about turbo header design in my new book (see GC Virtual Workshop) and you should read before proceeding.
G
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
Hello Guy,
thanks a lot, could you just let me know if by the term Header you mean Intercooler or is it sth different, if header = intercooler, does it mean then that the outgoing tubes are both at the same side?
thanks,
Rgds,
thanks a lot, could you just let me know if by the term Header you mean Intercooler or is it sth different, if header = intercooler, does it mean then that the outgoing tubes are both at the same side?
thanks,
Rgds,
Ritmo Abarth125TC
-
- Posts: 85
- Joined: June 22nd, 2006, 8:04 pm
- Location: Lomnice nad Popelkou (60 north from Prague), Czech Republic
- Contact:
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
Díky Honzo zajimavý to název pro svody.
Guy, I have info from Honza now.
Guy, I have info from Honza now.
Ritmo Abarth125TC
-
- Site Admin
- Posts: 5039
- Joined: June 18th, 2006, 9:31 am
- Location: Bedford, UK
- Contact:
Re: Fiat RITMO ABARTH 125TC
Some photos may illustrate, the flow results are only a small part of the problem one faces with turbo header design.
These tests on a standard head with 112cfm @10" bare port flow. The losses are due to turbulence caused by:
1. Bend radius
2. Pipe flare at port exit
3. Internal weld quality
I cannot over-emphasise that the design of a turbo header is extremely critical and with a bad design, port/cylinder overheating, detonation (not to mention loss of potential power) and fuel/ignition calibration difficulties are just a few of the possible consequences. The primary wave effects in particular can have an extreme effect on the firing cycles such that no two firing strokes are the same. You can imagine the problems that can cause with 'calibration'.
As I said, tons on this in my new book.
G
These tests on a standard head with 112cfm @10" bare port flow. The losses are due to turbulence caused by:
1. Bend radius
2. Pipe flare at port exit
3. Internal weld quality
I cannot over-emphasise that the design of a turbo header is extremely critical and with a bad design, port/cylinder overheating, detonation (not to mention loss of potential power) and fuel/ignition calibration difficulties are just a few of the possible consequences. The primary wave effects in particular can have an extreme effect on the firing cycles such that no two firing strokes are the same. You can imagine the problems that can cause with 'calibration'.
As I said, tons on this in my new book.
G
- Attachments
-
- header_01 port 1 giving 81cfm - best runner.jpg (453.09 KiB) Viewed 10895 times
-
- header_01 port 2 giving only 66.8cfm - worst runner.jpg (443.01 KiB) Viewed 10895 times
-
- UNASHAMED PLUG: COMING YOUR WAY SOON. IF YOU BUY ONE.
- BOOKS BOXED (450 x 600).jpg (172.92 KiB) Viewed 10894 times
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
first start - small joke - ETANOL
http://www.youtube.com/user/abarthTCT#p ... ByBLQZZOWY
second start - ETANOL:
http://www.youtube.com/user/abarthTCT#p ... lO_8NIRrB8
http://www.youtube.com/user/abarthTCT#p ... ByBLQZZOWY
second start - ETANOL:
http://www.youtube.com/user/abarthTCT#p ... lO_8NIRrB8
Ritmo Abarth125TC
-
- Posts: 33
- Joined: May 25th, 2008, 6:09 pm
- Location: CZ - Czech Republic, 47001 Česká Lípa
- Contact:
Re: Fiat RITMO ABARTH 125TC
Hi Guy, Hi all, last yer was not unacceptable for my Fiat, because I bougrt small house. I worked only few weeks but mthis yer will be for my Fiat good ...I think
- Attachments
-
- makrolon windows
- pict_20100807_211055.jpg (17.46 KiB) Viewed 9912 times
-
- a
- pict_20100807_211137.jpg (24.58 KiB) Viewed 9912 times
Ritmo Abarth125TC
Who is online
Users browsing this forum: No registered users and 0 guests