1977 Lancia Scorpion - Vx

Post pics of your car in here
fingers99
Posts: 99
Joined: December 9th, 2009, 6:24 pm
Contact:

Re: 1977 Lancia Scorpion - Vx

Post by fingers99 » May 3rd, 2013, 5:08 pm

I think the wheels need a centre bore of 58 (not 57) mm -- the factory tend to say 58.1mm, but............ do check!

Inner races stuck on hubs is pretty common. The safest way I've found to do it if either to mask up the top portion of the stub axle and run a bead of MIG down it, quench quickly with water and then from the top down (and wearing safety goggles) bop it with a cold chisel or do the same with a TIG torch (but don't do the bead!).

Basically, this puts a focussed line of heat in the shell, the quenching over-tempers it and makes it brittle, and the cold chisel cracks it along the weld bead. You can then just prise it off with an unloved screwdriver (or repeat on the other side).

Great project!
GC_06

lsmull
Posts: 20
Joined: February 14th, 2013, 5:24 pm
Contact:

Re: 1977 Lancia Scorpion - Vx

Post by lsmull » May 13th, 2013, 2:23 am

Nice tips I shall keep in mind, thanks.

Meantime, firewall is going in. With access panel protrusion for more airbox room. Raised the package shelf to max available as interior space there is pretty unseless and additional engine bay space will be sweet. We need to talk about the gasket/mounting configuration, But with a panel gasket, my newly crafted tunnel membrane, use of bulkhead connectors for brake/cluth lines, use of bulkhead wiring sockets, and of course, all the joint line welds, I am hoping interior fume penetration should be minimal, if at all. Note access panel should not impact rigidity given TMH cross member and the rear roll bars tying all the way down to the "frame rails". The new firewall's welds into good metal, roll beads, and angle iron frame will add to strength. New steel on rear shelf over exhaust is in as well. Vintage Customs have communicated very frequently and we've traded many pics and diagrams to ensure execution is on plan.
Attachments
CIMG3722 (800x600).jpg
New Steel
CIMG3722 (800x600).jpg (106.95 KiB) Viewed 2235 times
CIMG3724 (800x600).jpg
I think we'll use Teknofibra (space age stuff!) under here and inside the valence, and then again in the new exhaust box - plenty of good insulation this time around
CIMG3724 (800x600).jpg (103.62 KiB) Viewed 2235 times
CIMG3705 (800x600).jpg
Before
CIMG3705 (800x600).jpg (139.49 KiB) Viewed 2235 times
CIMG3764 (800x600).jpg
Angle stock frame
CIMG3764 (800x600).jpg (102.71 KiB) Viewed 2235 times
CIMG3796 (800x600).jpg
Locate the water pipe bracket
CIMG3796 (800x600).jpg (124.1 KiB) Viewed 2235 times
CIMG3802 (800x600).jpg
Johnny (right) is also doing much of the work on my Flaminia Sport - but he's liking the Scorp plan with its customization aspects
CIMG3802 (800x600).jpg (103.06 KiB) Viewed 2235 times
CIMG3803 (800x600).jpg
Nice recess for the panel to sit in
CIMG3803 (800x600).jpg (86.03 KiB) Viewed 2235 times
CIMG3805 (800x600).jpg
Cool helmet Johnny
CIMG3805 (800x600).jpg (92.08 KiB) Viewed 2235 times
CIMG3810 (800x600).jpg
Closer to "after" - not bad!
CIMG3810 (800x600).jpg (103.86 KiB) Viewed 2235 times
CIMG3812 (800x600).jpg
Plenty of clearance now - I budgeted conservatively
CIMG3812 (800x600).jpg (111.36 KiB) Viewed 2235 times
GC_09

Simon
Posts: 143
Joined: August 1st, 2009, 6:55 pm
Location: Leicester
Contact:

Re: 1977 Lancia Scorpion - Vx

Post by Simon » May 13th, 2013, 7:01 pm

That's coming along very nicely Ismull.
GC_15

Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests